Grab An Empty Plastic Bottle For A Smarter Way To Store Your Umbrellas

TL;DR

Before you orderOffer from Amazon

Get cleaning gear delivered free with Prime

• Fast, free delivery on millions of items
• Prime Video, Amazon Music and more included
• Member-only deals all year

Start your free Prime trial →Free trial for eligible customers · Cancel anytime

As an affiliate, we earn on qualifying purchases.Hide

A Hunker report describes a do-it-yourself umbrella holder made from a capped plastic bottle, string and basic cutting tools. The bottle hangs upside down to catch water from a folded umbrella, but users should empty it after each use and let the umbrella dry rather than leaving it wet inside.

Hunker has reported a DIY way to store wet umbrellas using an empty plastic bottle, string and basic cutting tools. The bottle is turned upside down to hold an umbrella and collect water. The report describes hanging the holder in a car or entryway.

The project uses a plastic bottle with a cap, string and something to cut the plastic. The bottle’s bottom is cut off, and the umbrella enters through the resulting wide opening. Two holes near the cut edge hold the string, which is knotted through the holes and tied into a loop for hanging. Hunker says water drains toward the bottle’s neck.

The report says the holder can be hung in a car or inside an entryway, or looped over a door handle. Hunker notes that the bottle should be washed before use, including removing its label, and that the finished holder can be left plain or decorated with paint, fabric or cord. Decorations should not block the cap or bottle opening.

For the cutting and string holes, the report describes using ordinary tools; it says YouTuber ABC Upcycling used a drill to make the holes. The source presents the holder as a way to contain drips temporarily, rather than for long-term storage. It advises opening the bottle and emptying it, and opening the umbrella indoors to dry.

A Reuse Option for Rainy-Day Drips

The idea addresses a familiar practical problem: a wet umbrella can drip onto car seats, vehicle floors or home flooring while it is being transported or kept near an entrance. A bottle with a cap provides a container for some of that runoff, and the added loop gives the holder a place to hang rather than leaving the umbrella on a porch or loose in a car.

Its appeal is also the low material cost and reuse of a household container. The report presents the holder as a small craft project rather than a tested commercial product. It does not provide measurements, leak testing or evidence that the design will suit every umbrella or bottle, so readers should treat it as a practical suggestion and check that their own version is stable and easy to empty.

Care matters after the rain stops. Standing water and a damp umbrella can encourage mildew, according to the report. Emptying the bottle and allowing the umbrella to dry reduces the chance that the holder becomes a place where moisture remains trapped.

How the Bottle Holder Works

The design relies on gravity and the shape of a capped bottle. With the bottle inverted and its base removed, the umbrella enters through the wide cut opening. Drips run down toward the narrower neck, where the cap keeps water from immediately spilling out. The holder can then be carried or hung by a loop made from string threaded through two holes.

Hunker describes water bottles and soft-drink bottles as possible materials and says the basic version needs only a bottle, string and something to cut the plastic. Its report also mentions washing off the label with dish soap, steam or a glue remover. Any decorating is optional; the cap needs to remain clear so collected water can be poured out.

The project is presented as an upcycling craft, not as a substitute for drying an umbrella. Hunker advises opening the bottle after each use to discard water, then opening the umbrella indoors until it dries. The source does not identify a particular bottle size or provide a weight limit, so the fit and hanging strength depend on the materials selected.

““All you need is a plastic bottle with a cap, something to cut the plastic, and string.””

— Hunker

Fit, Stability and Water Capacity

The supplied report does not state when the item was first published, provide independent testing, or quantify how much water the holder can collect. It also does not give a recommended bottle dimension, string length or maximum umbrella size. Those factors will vary with the bottle and umbrella used.

The source describes ways to make holes using a drill, knife or scissors, but it does not provide a detailed safety assessment for cutting plastic. The finished container’s leak resistance and hanging strength are also not established. Users would need to check that the cut edge is safe to handle, the loop is secure and the cap can be opened easily before hanging it over a surface that could be damaged by water.

Empty It and Dry the Umbrella

After each trip in the rain, Hunker recommends opening the bottle and pouring out collected water. The umbrella should then be opened indoors and allowed to dry before it is folded and put back in the holder. The report offers no further product testing or specifications; people trying the project will need to judge whether their bottle and string arrangement works for their own umbrella and intended hanging location.

Key Questions

What materials does the DIY umbrella holder require?

The basic project uses a plastic bottle with a cap, string and a tool for cutting the bottle. The report says a soft-drink bottle can be used and describes adding paint, fabric or cord as optional decoration.

How does the bottle catch umbrella water?

The bottle is turned upside down and its bottom is cut off, creating an opening for the folded umbrella. Drips run toward the bottle’s neck, where the cap holds water until the user opens it to empty the container.

Can a wet umbrella stay in the bottle?

No. Hunker advises against leaving a wet umbrella in the holder for a long time because moisture may lead to mildew. Empty the bottle after use and open the umbrella indoors so it can dry.

Where can the holder be hung?

The report suggests keeping one in a car or hanging it inside an entryway. It also says the loop could be placed over a back-door handle. The holder’s stability depends on the bottle, string and umbrella, which the source does not specify in detail.

Source: rss